Cardone 79-0273V Engine Control Module (ECM)
Remanufactured ECM for 2001 Dodge Ram
Cardone 79-0273V is a remanufactured engine control module for select 2001 Dodge Ram 1500, Ram 2500, and Ram 3500 applications with Federal Emission System calibration requirements. It is built for vehicle-specific flash programming and accurate VIN and mileage input, making it a direct-fit electronic control replacement for the listed Ram trucks.
Key Features
- Remanufactured Original Equipment-style engine control module for precise fitment
- Three rectangular connectors with 32-pin male terminals per connector bank
- Aluminum housing for OE-style mounting and durability
- Flash programming required for application-specific calibration
- Critical components are re-soldered or replaced during remanufacturing
- 100% computer tested for electrical function and reliability
- Earth-conscious remanufacturing process reduces raw material and energy use versus new part production
Product Details
Cardone’s Engine Control Module line focuses on restoring factory-level electronic control performance through remanufacturing and testing. For this part number 79-0273V, the module is rebuilt at Cardone’s Philadelphia manufacturing plant, where failed or weak components are corrected and the unit is validated before release. This approach is intended to address common ECM failure points such as poor power or ground circuits, wiring concerns, and shorted external components that can affect drivability on 2001 Dodge Ram 1500, Ram 2500, and Ram 3500 trucks.
This part cross-references Dodge OE numbers 56040273AA and 56040273AB for the same application.
Common Problems This ECM Can Address
- No-start or intermittent start conditions related to ECM failure
- Check engine light concerns caused by internal module faults
- Driveability issues tied to incorrect fuel or ignition control
- Communication problems between the ECM and vehicle systems
- Calibration mismatch after replacing a failed original module
Installation Notes
Fits 2001 Dodge Ram 1500, N/A; 2001 Dodge Ram 2500, N/A; and 2001 Dodge Ram 3500, N/A. Federal Emission System applications require vehicle-specific flash programming, and accurate VIN and mileage information are needed. Verify the original failure cause before replacement, including grounds, power feeds, wiring harness condition, and any shorted relays or solenoids. Chrysler PCM units identified with a “V” suffix require VIN programming. If the vehicle uses theft-deterrent programming, follow the OE service procedure for the specific application.
Quality Assurance
Cardone remanufactures this ECM to meet or exceed original equipment performance expectations through component-level repair and computer testing. Each unit is validated for function before release, and the remanufacturing process is designed to restore reliable electronic control for the listed Dodge Ram applications.
Cardone 79-0273V Engine Control Module (ECM)
Remanufactured ECM for 2001 Dodge Ram
Cardone 79-0273V is a remanufactured engine control module for select 2001 Dodge Ram 1500, Ram 2500, and Ram 3500 applications with Federal Emission System calibration requirements. It is built for vehicle-specific flash programming and accurate VIN and mileage input, making it a direct-fit electronic control replacement for the listed Ram trucks.
Key Features
- Remanufactured Original Equipment-style engine control module for precise fitment
- Three rectangular connectors with 32-pin male terminals per connector bank
- Aluminum housing for OE-style mounting and durability
- Flash programming required for application-specific calibration
- Critical components are re-soldered or replaced during remanufacturing
- 100% computer tested for electrical function and reliability
- Earth-conscious remanufacturing process reduces raw material and energy use versus new part production
Product Details
Cardone’s Engine Control Module line focuses on restoring factory-level electronic control performance through remanufacturing and testing. For this part number 79-0273V, the module is rebuilt at Cardone’s Philadelphia manufacturing plant, where failed or weak components are corrected and the unit is validated before release. This approach is intended to address common ECM failure points such as poor power or ground circuits, wiring concerns, and shorted external components that can affect drivability on 2001 Dodge Ram 1500, Ram 2500, and Ram 3500 trucks.
This part cross-references Dodge OE numbers 56040273AA and 56040273AB for the same application.
Common Problems This ECM Can Address
- No-start or intermittent start conditions related to ECM failure
- Check engine light concerns caused by internal module faults
- Driveability issues tied to incorrect fuel or ignition control
- Communication problems between the ECM and vehicle systems
- Calibration mismatch after replacing a failed original module
Installation Notes
Fits 2001 Dodge Ram 1500, N/A; 2001 Dodge Ram 2500, N/A; and 2001 Dodge Ram 3500, N/A. Federal Emission System applications require vehicle-specific flash programming, and accurate VIN and mileage information are needed. Verify the original failure cause before replacement, including grounds, power feeds, wiring harness condition, and any shorted relays or solenoids. Chrysler PCM units identified with a “V” suffix require VIN programming. If the vehicle uses theft-deterrent programming, follow the OE service procedure for the specific application.
Quality Assurance
Cardone remanufactures this ECM to meet or exceed original equipment performance expectations through component-level repair and computer testing. Each unit is validated for function before release, and the remanufacturing process is designed to restore reliable electronic control for the listed Dodge Ram applications.
Product Information
Product Information
Shipping & Returns
Shipping & Returns
Description
Remanufactured ECM for 2001 Dodge Ram
Cardone 79-0273V is a remanufactured engine control module for select 2001 Dodge Ram 1500, Ram 2500, and Ram 3500 applications with Federal Emission System calibration requirements. It is built for vehicle-specific flash programming and accurate VIN and mileage input, making it a direct-fit electronic control replacement for the listed Ram trucks.
Key Features
- Remanufactured Original Equipment-style engine control module for precise fitment
- Three rectangular connectors with 32-pin male terminals per connector bank
- Aluminum housing for OE-style mounting and durability
- Flash programming required for application-specific calibration
- Critical components are re-soldered or replaced during remanufacturing
- 100% computer tested for electrical function and reliability
- Earth-conscious remanufacturing process reduces raw material and energy use versus new part production
Product Details
Cardone’s Engine Control Module line focuses on restoring factory-level electronic control performance through remanufacturing and testing. For this part number 79-0273V, the module is rebuilt at Cardone’s Philadelphia manufacturing plant, where failed or weak components are corrected and the unit is validated before release. This approach is intended to address common ECM failure points such as poor power or ground circuits, wiring concerns, and shorted external components that can affect drivability on 2001 Dodge Ram 1500, Ram 2500, and Ram 3500 trucks.
This part cross-references Dodge OE numbers 56040273AA and 56040273AB for the same application.
Common Problems This ECM Can Address
- No-start or intermittent start conditions related to ECM failure
- Check engine light concerns caused by internal module faults
- Driveability issues tied to incorrect fuel or ignition control
- Communication problems between the ECM and vehicle systems
- Calibration mismatch after replacing a failed original module
Installation Notes
Fits 2001 Dodge Ram 1500, N/A; 2001 Dodge Ram 2500, N/A; and 2001 Dodge Ram 3500, N/A. Federal Emission System applications require vehicle-specific flash programming, and accurate VIN and mileage information are needed. Verify the original failure cause before replacement, including grounds, power feeds, wiring harness condition, and any shorted relays or solenoids. Chrysler PCM units identified with a “V” suffix require VIN programming. If the vehicle uses theft-deterrent programming, follow the OE service procedure for the specific application.
Quality Assurance
Cardone remanufactures this ECM to meet or exceed original equipment performance expectations through component-level repair and computer testing. Each unit is validated for function before release, and the remanufacturing process is designed to restore reliable electronic control for the listed Dodge Ram applications.
