Dorman 532-487 Suspension Control Arm Bushing - Front Lower Arm To Torsion Bar
OE-Style Suspension Control Arm Bushing
Dorman 532-487 is a suspension control arm bushing engineered as a direct replacement for the original equipment on specific Honda and Acura applications. It uses rubber construction and OE-style dimensions to restore the connection between the control arm and torsion bar on the listed vehicles.
Compatible With 1984-1987 Honda Civic, front lower arm to torsion bar, and 1986-1989 Acura Integra, front lower arm to torsion bar. The Dorman 532-487 bushing is built for a precise fit where the suspension pivots and loads transfer through the control arm assembly.
- Rubber construction for suspension isolation
- Black finish
- Mounting type: bushing
- Inside diameter: 35 mm
- Outside diameter: 58.8 mm
- Length: 35.2 mm
- Width: 60 mm
- Bracket not included
- Mounting hardware not included
Detailed Product Overview
This suspension control arm bushing is precision-engineered and tested to replace the original equipment part on specific vehicles. Dorman 532-487 is designed around the factory-style bushing dimensions, including 12.2 mm inner diameters and the listed outer widths, to help maintain proper suspension geometry at the front lower arm to torsion bar location. For shoppers searching for a Honda Civic front lower arm to torsion bar bushing or an Acura Integra suspension control arm bushing, this part number provides a direct-reference option for the listed applications. This part cross-references Monroe Shocks & Struts (e.g., 172286, 182286) for the same application.
What It Helps Address
- Excessive play in the front suspension pivot point
- Clunking or knocking from worn control arm bushings
- Uneven suspension response caused by deteriorated rubber
- Loss of factory-style control arm alignment at the torsion bar connection
- Replacement needs for aging Honda Civic and Acura Integra suspension bushings
Installation Notes
Verify the vehicle position and suspension layout before installation. This bushing is for the front lower arm to torsion bar location on the listed Honda Civic and Acura Integra applications. Inspect the control arm and surrounding mounting surfaces for wear or damage before pressing in the replacement bushing, and confirm all dimensions match the original part before assembly.
Quality Assurance
Dorman manufactures this control arm bushing as a tested replacement part for specific OE applications. The design follows the original equipment fit and function requirements for the listed vehicles, supporting consistent suspension service on Honda Civic and Acura Integra models.
Dorman 532-487 Suspension Control Arm Bushing - Front Lower Arm To Torsion Bar
OE-Style Suspension Control Arm Bushing
Dorman 532-487 is a suspension control arm bushing engineered as a direct replacement for the original equipment on specific Honda and Acura applications. It uses rubber construction and OE-style dimensions to restore the connection between the control arm and torsion bar on the listed vehicles.
Compatible With 1984-1987 Honda Civic, front lower arm to torsion bar, and 1986-1989 Acura Integra, front lower arm to torsion bar. The Dorman 532-487 bushing is built for a precise fit where the suspension pivots and loads transfer through the control arm assembly.
- Rubber construction for suspension isolation
- Black finish
- Mounting type: bushing
- Inside diameter: 35 mm
- Outside diameter: 58.8 mm
- Length: 35.2 mm
- Width: 60 mm
- Bracket not included
- Mounting hardware not included
Detailed Product Overview
This suspension control arm bushing is precision-engineered and tested to replace the original equipment part on specific vehicles. Dorman 532-487 is designed around the factory-style bushing dimensions, including 12.2 mm inner diameters and the listed outer widths, to help maintain proper suspension geometry at the front lower arm to torsion bar location. For shoppers searching for a Honda Civic front lower arm to torsion bar bushing or an Acura Integra suspension control arm bushing, this part number provides a direct-reference option for the listed applications. This part cross-references Monroe Shocks & Struts (e.g., 172286, 182286) for the same application.
What It Helps Address
- Excessive play in the front suspension pivot point
- Clunking or knocking from worn control arm bushings
- Uneven suspension response caused by deteriorated rubber
- Loss of factory-style control arm alignment at the torsion bar connection
- Replacement needs for aging Honda Civic and Acura Integra suspension bushings
Installation Notes
Verify the vehicle position and suspension layout before installation. This bushing is for the front lower arm to torsion bar location on the listed Honda Civic and Acura Integra applications. Inspect the control arm and surrounding mounting surfaces for wear or damage before pressing in the replacement bushing, and confirm all dimensions match the original part before assembly.
Quality Assurance
Dorman manufactures this control arm bushing as a tested replacement part for specific OE applications. The design follows the original equipment fit and function requirements for the listed vehicles, supporting consistent suspension service on Honda Civic and Acura Integra models.
Product Information
Product Information
Shipping & Returns
Shipping & Returns
Description
OE-Style Suspension Control Arm Bushing
Dorman 532-487 is a suspension control arm bushing engineered as a direct replacement for the original equipment on specific Honda and Acura applications. It uses rubber construction and OE-style dimensions to restore the connection between the control arm and torsion bar on the listed vehicles.
Compatible With 1984-1987 Honda Civic, front lower arm to torsion bar, and 1986-1989 Acura Integra, front lower arm to torsion bar. The Dorman 532-487 bushing is built for a precise fit where the suspension pivots and loads transfer through the control arm assembly.
- Rubber construction for suspension isolation
- Black finish
- Mounting type: bushing
- Inside diameter: 35 mm
- Outside diameter: 58.8 mm
- Length: 35.2 mm
- Width: 60 mm
- Bracket not included
- Mounting hardware not included
Detailed Product Overview
This suspension control arm bushing is precision-engineered and tested to replace the original equipment part on specific vehicles. Dorman 532-487 is designed around the factory-style bushing dimensions, including 12.2 mm inner diameters and the listed outer widths, to help maintain proper suspension geometry at the front lower arm to torsion bar location. For shoppers searching for a Honda Civic front lower arm to torsion bar bushing or an Acura Integra suspension control arm bushing, this part number provides a direct-reference option for the listed applications. This part cross-references Monroe Shocks & Struts (e.g., 172286, 182286) for the same application.
What It Helps Address
- Excessive play in the front suspension pivot point
- Clunking or knocking from worn control arm bushings
- Uneven suspension response caused by deteriorated rubber
- Loss of factory-style control arm alignment at the torsion bar connection
- Replacement needs for aging Honda Civic and Acura Integra suspension bushings
Installation Notes
Verify the vehicle position and suspension layout before installation. This bushing is for the front lower arm to torsion bar location on the listed Honda Civic and Acura Integra applications. Inspect the control arm and surrounding mounting surfaces for wear or damage before pressing in the replacement bushing, and confirm all dimensions match the original part before assembly.
Quality Assurance
Dorman manufactures this control arm bushing as a tested replacement part for specific OE applications. The design follows the original equipment fit and function requirements for the listed vehicles, supporting consistent suspension service on Honda Civic and Acura Integra models.
