Dorman 533-648 Suspension Control Arm Bushing - Front Lower Rearward
Dorman 533-648 Suspension Control Arm Bushing
Dorman 533-648 is a standard replacement suspension control arm bushing built for specific vehicle applications that require a direct-fit OE-style service part. It uses a steel and rubber construction to restore the control arm’s mounting interface and help maintain suspension alignment and ride control.
Compatible With select make/model applications, including vehicle-specific suspension service needs where a control arm bushing is specified. This part number, 533-648, is engineered and tested for reliable replacement performance on the original equipment application.
Key Features
- Suspension control arm bushing for OE-style replacement
- Steel and rubber construction for strength and isolation
- Standard replacement grade
- Black finish
- Precision-engineered and rigorously tested by Dorman
- Direct replacement part number: 533-648
Detailed Description
Dorman 533-648 is a suspension control arm bushing designed to replace the original equipment bushing on specific vehicles. The steel and rubber design supports the control arm mounting point while helping isolate road vibration through the suspension. With dimensions including a 12.2 mm inside diameter, 60 mm length and width, 66.2 mm height, 60 mm outside diameter, 23.8 mm wall thickness, 18.4 mm mounting hole diameter, and 62.8 mm distance between mounting holes, this bushing is built around application-specific measurements for accurate service replacement. If you are searching for a Dorman 533-648 control arm bushing for suspension repair, this part is intended for the same type of OE replacement work commonly needed on select make/model vehicles.
This part cross-references Monroe Shocks & Struts (e.g., 172286, 182286) for the same application.
Common Problems It Can Help Address
- Excessive suspension play from a worn control arm bushing
- Clunking or knocking noises from the front or rear suspension mounting point
- Uneven tire wear caused by loosened suspension geometry
- Steering wander or reduced road feel linked to bushing wear
- Cracked, hardened, or deteriorated rubber in the control arm mount
Installation Notes and Tips
Verify the vehicle’s original bushing dimensions and mounting style before installation. Because this part is a bushing-only replacement, inspect the control arm, mounting bores, and surrounding suspension components for wear or damage before pressing in the new part. Professional installation and proper suspension alignment are recommended after service. Search terms such as Dorman 533-648 suspension control arm bushing, control arm bushing replacement, and OE-style suspension bushing are commonly used when sourcing this part for make/model-specific repairs.
Quality Assurance
Dorman states that this suspension control arm bushing is precision-engineered and rigorously tested to provide reliable replacement for the original equipment on specific vehicles. The part is a standard replacement component built to match the application requirements of the original suspension service part.
Dorman 533-648 Suspension Control Arm Bushing - Front Lower Rearward
Dorman 533-648 Suspension Control Arm Bushing
Dorman 533-648 is a standard replacement suspension control arm bushing built for specific vehicle applications that require a direct-fit OE-style service part. It uses a steel and rubber construction to restore the control arm’s mounting interface and help maintain suspension alignment and ride control.
Compatible With select make/model applications, including vehicle-specific suspension service needs where a control arm bushing is specified. This part number, 533-648, is engineered and tested for reliable replacement performance on the original equipment application.
Key Features
- Suspension control arm bushing for OE-style replacement
- Steel and rubber construction for strength and isolation
- Standard replacement grade
- Black finish
- Precision-engineered and rigorously tested by Dorman
- Direct replacement part number: 533-648
Detailed Description
Dorman 533-648 is a suspension control arm bushing designed to replace the original equipment bushing on specific vehicles. The steel and rubber design supports the control arm mounting point while helping isolate road vibration through the suspension. With dimensions including a 12.2 mm inside diameter, 60 mm length and width, 66.2 mm height, 60 mm outside diameter, 23.8 mm wall thickness, 18.4 mm mounting hole diameter, and 62.8 mm distance between mounting holes, this bushing is built around application-specific measurements for accurate service replacement. If you are searching for a Dorman 533-648 control arm bushing for suspension repair, this part is intended for the same type of OE replacement work commonly needed on select make/model vehicles.
This part cross-references Monroe Shocks & Struts (e.g., 172286, 182286) for the same application.
Common Problems It Can Help Address
- Excessive suspension play from a worn control arm bushing
- Clunking or knocking noises from the front or rear suspension mounting point
- Uneven tire wear caused by loosened suspension geometry
- Steering wander or reduced road feel linked to bushing wear
- Cracked, hardened, or deteriorated rubber in the control arm mount
Installation Notes and Tips
Verify the vehicle’s original bushing dimensions and mounting style before installation. Because this part is a bushing-only replacement, inspect the control arm, mounting bores, and surrounding suspension components for wear or damage before pressing in the new part. Professional installation and proper suspension alignment are recommended after service. Search terms such as Dorman 533-648 suspension control arm bushing, control arm bushing replacement, and OE-style suspension bushing are commonly used when sourcing this part for make/model-specific repairs.
Quality Assurance
Dorman states that this suspension control arm bushing is precision-engineered and rigorously tested to provide reliable replacement for the original equipment on specific vehicles. The part is a standard replacement component built to match the application requirements of the original suspension service part.
Product Information
Product Information
Shipping & Returns
Shipping & Returns
Description
Dorman 533-648 Suspension Control Arm Bushing
Dorman 533-648 is a standard replacement suspension control arm bushing built for specific vehicle applications that require a direct-fit OE-style service part. It uses a steel and rubber construction to restore the control arm’s mounting interface and help maintain suspension alignment and ride control.
Compatible With select make/model applications, including vehicle-specific suspension service needs where a control arm bushing is specified. This part number, 533-648, is engineered and tested for reliable replacement performance on the original equipment application.
Key Features
- Suspension control arm bushing for OE-style replacement
- Steel and rubber construction for strength and isolation
- Standard replacement grade
- Black finish
- Precision-engineered and rigorously tested by Dorman
- Direct replacement part number: 533-648
Detailed Description
Dorman 533-648 is a suspension control arm bushing designed to replace the original equipment bushing on specific vehicles. The steel and rubber design supports the control arm mounting point while helping isolate road vibration through the suspension. With dimensions including a 12.2 mm inside diameter, 60 mm length and width, 66.2 mm height, 60 mm outside diameter, 23.8 mm wall thickness, 18.4 mm mounting hole diameter, and 62.8 mm distance between mounting holes, this bushing is built around application-specific measurements for accurate service replacement. If you are searching for a Dorman 533-648 control arm bushing for suspension repair, this part is intended for the same type of OE replacement work commonly needed on select make/model vehicles.
This part cross-references Monroe Shocks & Struts (e.g., 172286, 182286) for the same application.
Common Problems It Can Help Address
- Excessive suspension play from a worn control arm bushing
- Clunking or knocking noises from the front or rear suspension mounting point
- Uneven tire wear caused by loosened suspension geometry
- Steering wander or reduced road feel linked to bushing wear
- Cracked, hardened, or deteriorated rubber in the control arm mount
Installation Notes and Tips
Verify the vehicle’s original bushing dimensions and mounting style before installation. Because this part is a bushing-only replacement, inspect the control arm, mounting bores, and surrounding suspension components for wear or damage before pressing in the new part. Professional installation and proper suspension alignment are recommended after service. Search terms such as Dorman 533-648 suspension control arm bushing, control arm bushing replacement, and OE-style suspension bushing are commonly used when sourcing this part for make/model-specific repairs.
Quality Assurance
Dorman states that this suspension control arm bushing is precision-engineered and rigorously tested to provide reliable replacement for the original equipment on specific vehicles. The part is a standard replacement component built to match the application requirements of the original suspension service part.
