Dorman 533-661 Suspension Control Arm Bushing - Front Lower Rearward
Dorman 533-661 Suspension Control Arm Bushing
Dorman 533-661 is a standard replacement suspension control arm bushing built for specific vehicle applications that require an OE-style service part. It uses steel and rubber construction to restore the control arm’s mounting interface and help maintain suspension alignment and ride control.
Key Features
- Precision-engineered suspension control arm bushing for direct replacement use
- Steel and rubber construction for strength and vibration isolation
- Standard replacement grade for service and repair work
- Black/gray finish with OE-style dimensions: 45.5 length, 60.2 outside diameter, 12.8 inside diameter
- Mounting hole diameter: 18.4; distance between mounting holes: 62.8
- Dust boot, bracket, and mounting hardware are not included
- Cross-references Gates 352310 and 352320 for the same application
Detailed Description
This suspension control arm bushing is engineered for vehicles that need a replacement bushing with the correct fit, material mix, and mounting dimensions. The steel and rubber design helps support the control arm while reducing unwanted movement at the suspension pivot point. Dorman 533-661 is a practical choice for suspension service on vehicles where worn bushings can affect steering feel, tire wear, and chassis stability. If you are sourcing a Dorman 533-661 replacement for a suspension repair, this part is built to match the original equipment style used on specific applications.
What It Helps Fix
- Clunking or knocking noises from worn suspension bushings
- Excessive control arm movement under load
- Loose or imprecise steering response
- Uneven tire wear caused by suspension play
- Vibration transfer through the control arm mounting point
Installation Notes and Tips
Inspect the control arm, mounting points, and surrounding suspension components before installation. Press-fit bushing service typically requires proper suspension tools and accurate alignment of the bushing to the control arm. Verify dimensions and vehicle application before ordering, especially when replacing a worn original bushing on a make/model-specific suspension setup. For buyers searching for a Dorman 533-661 control arm bushing for suspension repair, confirm the original part style and mounting measurements against the removed component.
Quality Assurance
Dorman states that this part is precision-engineered and rigorously tested to serve as a reliable replacement for the original equipment on specific vehicles. That focus on dimensional accuracy and material selection supports consistent service performance in suspension repair work.
Original: $20.22
-65%$20.22
$7.08Dorman 533-661 Suspension Control Arm Bushing - Front Lower Rearward
Dorman 533-661 Suspension Control Arm Bushing
Dorman 533-661 is a standard replacement suspension control arm bushing built for specific vehicle applications that require an OE-style service part. It uses steel and rubber construction to restore the control arm’s mounting interface and help maintain suspension alignment and ride control.
Key Features
- Precision-engineered suspension control arm bushing for direct replacement use
- Steel and rubber construction for strength and vibration isolation
- Standard replacement grade for service and repair work
- Black/gray finish with OE-style dimensions: 45.5 length, 60.2 outside diameter, 12.8 inside diameter
- Mounting hole diameter: 18.4; distance between mounting holes: 62.8
- Dust boot, bracket, and mounting hardware are not included
- Cross-references Gates 352310 and 352320 for the same application
Detailed Description
This suspension control arm bushing is engineered for vehicles that need a replacement bushing with the correct fit, material mix, and mounting dimensions. The steel and rubber design helps support the control arm while reducing unwanted movement at the suspension pivot point. Dorman 533-661 is a practical choice for suspension service on vehicles where worn bushings can affect steering feel, tire wear, and chassis stability. If you are sourcing a Dorman 533-661 replacement for a suspension repair, this part is built to match the original equipment style used on specific applications.
What It Helps Fix
- Clunking or knocking noises from worn suspension bushings
- Excessive control arm movement under load
- Loose or imprecise steering response
- Uneven tire wear caused by suspension play
- Vibration transfer through the control arm mounting point
Installation Notes and Tips
Inspect the control arm, mounting points, and surrounding suspension components before installation. Press-fit bushing service typically requires proper suspension tools and accurate alignment of the bushing to the control arm. Verify dimensions and vehicle application before ordering, especially when replacing a worn original bushing on a make/model-specific suspension setup. For buyers searching for a Dorman 533-661 control arm bushing for suspension repair, confirm the original part style and mounting measurements against the removed component.
Quality Assurance
Dorman states that this part is precision-engineered and rigorously tested to serve as a reliable replacement for the original equipment on specific vehicles. That focus on dimensional accuracy and material selection supports consistent service performance in suspension repair work.
Product Information
Product Information
Shipping & Returns
Shipping & Returns
Description
Dorman 533-661 Suspension Control Arm Bushing
Dorman 533-661 is a standard replacement suspension control arm bushing built for specific vehicle applications that require an OE-style service part. It uses steel and rubber construction to restore the control arm’s mounting interface and help maintain suspension alignment and ride control.
Key Features
- Precision-engineered suspension control arm bushing for direct replacement use
- Steel and rubber construction for strength and vibration isolation
- Standard replacement grade for service and repair work
- Black/gray finish with OE-style dimensions: 45.5 length, 60.2 outside diameter, 12.8 inside diameter
- Mounting hole diameter: 18.4; distance between mounting holes: 62.8
- Dust boot, bracket, and mounting hardware are not included
- Cross-references Gates 352310 and 352320 for the same application
Detailed Description
This suspension control arm bushing is engineered for vehicles that need a replacement bushing with the correct fit, material mix, and mounting dimensions. The steel and rubber design helps support the control arm while reducing unwanted movement at the suspension pivot point. Dorman 533-661 is a practical choice for suspension service on vehicles where worn bushings can affect steering feel, tire wear, and chassis stability. If you are sourcing a Dorman 533-661 replacement for a suspension repair, this part is built to match the original equipment style used on specific applications.
What It Helps Fix
- Clunking or knocking noises from worn suspension bushings
- Excessive control arm movement under load
- Loose or imprecise steering response
- Uneven tire wear caused by suspension play
- Vibration transfer through the control arm mounting point
Installation Notes and Tips
Inspect the control arm, mounting points, and surrounding suspension components before installation. Press-fit bushing service typically requires proper suspension tools and accurate alignment of the bushing to the control arm. Verify dimensions and vehicle application before ordering, especially when replacing a worn original bushing on a make/model-specific suspension setup. For buyers searching for a Dorman 533-661 control arm bushing for suspension repair, confirm the original part style and mounting measurements against the removed component.
Quality Assurance
Dorman states that this part is precision-engineered and rigorously tested to serve as a reliable replacement for the original equipment on specific vehicles. That focus on dimensional accuracy and material selection supports consistent service performance in suspension repair work.
