Dorman 533-688 Suspension Control Arm Bushing - Front Lower Rearward
OE-Style Suspension Control Arm Bushing
Dorman 533-688 is a suspension control arm bushing engineered as a standard replacement for the original equipment design on select Volkswagen vehicles. It uses rubber and steel construction to restore the control arm’s mounting point with the correct fit for front lower rearward applications.
Compatible with Volkswagen Golf, Jetta, Passat, Corrado, Cabrio, Derby, and Van applications, this bushing is built for direct replacement service on the front lower rearward position. The Dorman 533-688 part number is also referenced by several aftermarket and OE-style cross numbers for the same application.
Key Features
- Standard replacement suspension control arm bushing
- Rubber and steel bushing material for OE-style service
- Black/gray finish
- Inside diameter: 17.2 mm
- Outside diameter: 60.5 mm
- Width: 60 mm
- Height: 66.2 mm
- Mounting hole diameter: 18.4 mm
- Distance between mounting holes: 62.8 mm
- No dust boot, bracket, or mounting hardware included
Detailed Description
Dorman 533-688 is a suspension control arm bushing for the front lower rearward position on select Volkswagen models. It is precision-engineered and tested to replace the original equipment bushing on applications such as the Volkswagen Golf, Jetta, Passat, Corrado, Cabrio, Derby, and Van. The rubber and steel construction supports a direct-fit repair where the control arm bushing has worn, cracked, or lost its original isolation characteristics.
This part cross-references MOOG Chassis Products K200092 for the same application. The Dorman 533-688 part number is commonly used when servicing front lower rearward control arm bushing wear on Volkswagen Golf and Jetta platforms, as well as other listed VW applications.
What It Is Used For
- Replacing a worn front lower rearward control arm bushing
- Correcting looseness in the suspension mounting point
- Addressing clunking or knocking from deteriorated bushing material
- Restoring control arm alignment at the mounting location
- Repairing cracked, separated, or compressed rubber bushings
Installation Notes and Tips
Verify the vehicle’s front lower rearward control arm position before ordering. Compare the original bushing dimensions, mounting hole spacing, and inside diameter to Dorman 533-688 for proper match-up. Because mounting hardware is not included, reuse or replace related fasteners as needed during service. Press-fit suspension bushings typically require proper tools and alignment during installation.
Quality Assurance
This Dorman suspension bushing is manufactured as a standard replacement part and rigorously tested for reliable service on the listed Volkswagen applications. It is built to meet the demands of OE-style suspension repair for Volkswagen Golf, Jetta, Passat, Corrado, Cabrio, Derby, and Van models.
Original: $24.43
-65%$24.43
$8.55Dorman 533-688 Suspension Control Arm Bushing - Front Lower Rearward
OE-Style Suspension Control Arm Bushing
Dorman 533-688 is a suspension control arm bushing engineered as a standard replacement for the original equipment design on select Volkswagen vehicles. It uses rubber and steel construction to restore the control arm’s mounting point with the correct fit for front lower rearward applications.
Compatible with Volkswagen Golf, Jetta, Passat, Corrado, Cabrio, Derby, and Van applications, this bushing is built for direct replacement service on the front lower rearward position. The Dorman 533-688 part number is also referenced by several aftermarket and OE-style cross numbers for the same application.
Key Features
- Standard replacement suspension control arm bushing
- Rubber and steel bushing material for OE-style service
- Black/gray finish
- Inside diameter: 17.2 mm
- Outside diameter: 60.5 mm
- Width: 60 mm
- Height: 66.2 mm
- Mounting hole diameter: 18.4 mm
- Distance between mounting holes: 62.8 mm
- No dust boot, bracket, or mounting hardware included
Detailed Description
Dorman 533-688 is a suspension control arm bushing for the front lower rearward position on select Volkswagen models. It is precision-engineered and tested to replace the original equipment bushing on applications such as the Volkswagen Golf, Jetta, Passat, Corrado, Cabrio, Derby, and Van. The rubber and steel construction supports a direct-fit repair where the control arm bushing has worn, cracked, or lost its original isolation characteristics.
This part cross-references MOOG Chassis Products K200092 for the same application. The Dorman 533-688 part number is commonly used when servicing front lower rearward control arm bushing wear on Volkswagen Golf and Jetta platforms, as well as other listed VW applications.
What It Is Used For
- Replacing a worn front lower rearward control arm bushing
- Correcting looseness in the suspension mounting point
- Addressing clunking or knocking from deteriorated bushing material
- Restoring control arm alignment at the mounting location
- Repairing cracked, separated, or compressed rubber bushings
Installation Notes and Tips
Verify the vehicle’s front lower rearward control arm position before ordering. Compare the original bushing dimensions, mounting hole spacing, and inside diameter to Dorman 533-688 for proper match-up. Because mounting hardware is not included, reuse or replace related fasteners as needed during service. Press-fit suspension bushings typically require proper tools and alignment during installation.
Quality Assurance
This Dorman suspension bushing is manufactured as a standard replacement part and rigorously tested for reliable service on the listed Volkswagen applications. It is built to meet the demands of OE-style suspension repair for Volkswagen Golf, Jetta, Passat, Corrado, Cabrio, Derby, and Van models.
Product Information
Product Information
Shipping & Returns
Shipping & Returns
Description
OE-Style Suspension Control Arm Bushing
Dorman 533-688 is a suspension control arm bushing engineered as a standard replacement for the original equipment design on select Volkswagen vehicles. It uses rubber and steel construction to restore the control arm’s mounting point with the correct fit for front lower rearward applications.
Compatible with Volkswagen Golf, Jetta, Passat, Corrado, Cabrio, Derby, and Van applications, this bushing is built for direct replacement service on the front lower rearward position. The Dorman 533-688 part number is also referenced by several aftermarket and OE-style cross numbers for the same application.
Key Features
- Standard replacement suspension control arm bushing
- Rubber and steel bushing material for OE-style service
- Black/gray finish
- Inside diameter: 17.2 mm
- Outside diameter: 60.5 mm
- Width: 60 mm
- Height: 66.2 mm
- Mounting hole diameter: 18.4 mm
- Distance between mounting holes: 62.8 mm
- No dust boot, bracket, or mounting hardware included
Detailed Description
Dorman 533-688 is a suspension control arm bushing for the front lower rearward position on select Volkswagen models. It is precision-engineered and tested to replace the original equipment bushing on applications such as the Volkswagen Golf, Jetta, Passat, Corrado, Cabrio, Derby, and Van. The rubber and steel construction supports a direct-fit repair where the control arm bushing has worn, cracked, or lost its original isolation characteristics.
This part cross-references MOOG Chassis Products K200092 for the same application. The Dorman 533-688 part number is commonly used when servicing front lower rearward control arm bushing wear on Volkswagen Golf and Jetta platforms, as well as other listed VW applications.
What It Is Used For
- Replacing a worn front lower rearward control arm bushing
- Correcting looseness in the suspension mounting point
- Addressing clunking or knocking from deteriorated bushing material
- Restoring control arm alignment at the mounting location
- Repairing cracked, separated, or compressed rubber bushings
Installation Notes and Tips
Verify the vehicle’s front lower rearward control arm position before ordering. Compare the original bushing dimensions, mounting hole spacing, and inside diameter to Dorman 533-688 for proper match-up. Because mounting hardware is not included, reuse or replace related fasteners as needed during service. Press-fit suspension bushings typically require proper tools and alignment during installation.
Quality Assurance
This Dorman suspension bushing is manufactured as a standard replacement part and rigorously tested for reliable service on the listed Volkswagen applications. It is built to meet the demands of OE-style suspension repair for Volkswagen Golf, Jetta, Passat, Corrado, Cabrio, Derby, and Van models.
