Pagid 355252791 Disc Brake Pad Wear Sensor - Rear
Rear Brake Pad Wear Sensor for Audi Applications
This Pagid disc brake pad wear sensor is built for rear brake systems and uses a 395 mm wiring harness with a male connector for a direct-style replacement. It is engineered for Audi vehicles that rely on electronic pad wear monitoring, including A4, A5, Q7, Q8, S4, S5, S8, SQ7, SQ8, RS5, RS6 Avant, and RS7 Sportback applications.
Part number 355252791 is designed with durable injection-molded construction to handle demanding driving conditions and help maintain reliable brake wear signal performance. If you are replacing a rear brake pad wear sensor on an Audi A4 Quattro, Audi Q7, or Audi S5 Sportback, this sensor supports the factory monitoring system with the correct harness length and connector style.
Key Features
- Disc brake pad wear sensor for rear brake applications
- 395 mm / 15.55 in wiring harness length
- Male connector for the vehicle-side interface
- Wiring harness included for installation-ready replacement
- Injection-molded construction for durability in harsh environments
- Technical Information Number: P8713
- Pagid part number 355252791
Detailed Product Information
Pagid 355252791 is a rear disc brake pad wear sensor intended for vehicles equipped with electronic brake wear monitoring. The sensor is built to match the demands of modern Audi brake systems and is suited for models such as the Audi A4 allroad, A5 Sportback, A8 Quattro, Q7, Q8, RS5 Sportback, RS6 Avant, RS7 Sportback, S4, S5, S8, SQ7, and SQ8. This part cross-references Monroe Shocks & Struts (e.g., 172286, 182286) for the same application.
For shoppers searching for a rear brake pad wear sensor for Audi A4 Quattro, rear brake pad wear sensor for Audi Q7, or Pagid 355252791 for Audi S5, this part provides the fitment and connector details needed for a proper replacement. It is also listed for select RS Q8, RS6 Avant, and RS7 Sportback applications with ceramic brake exclusions noted where applicable.
What This Part Helps Address
- Brake wear warning light staying on after pad service
- Damaged or broken rear pad wear sensor wiring
- Fault codes related to brake pad wear monitoring
- Intermittent brake wear signal loss from heat or road exposure
- Replacement needs after rear brake pad and rotor service
Installation Notes and Tips
Installation requires qualified personnel. Confirm rear axle fitment, connector style, and harness routing before installation. Inspect the brake pad wear sensor path for abrasion points, damaged clips, or heat exposure, and verify the sensor seats correctly in the pad carrier and brake pad groove. After installation, clear any stored wear-related fault codes and confirm the warning system resets properly.
Quality Assurance
HELLA brake pad wear sensor engineering is referenced by the manufacturer description, with emphasis on precise fitment, durable injection-molded construction, and dependable performance across varied driving conditions. Pagid part number 355252791 is built for rear disc brake monitoring on supported Audi applications and is identified with Technical Information Number P8713.
Pagid 355252791 Disc Brake Pad Wear Sensor - Rear
Rear Brake Pad Wear Sensor for Audi Applications
This Pagid disc brake pad wear sensor is built for rear brake systems and uses a 395 mm wiring harness with a male connector for a direct-style replacement. It is engineered for Audi vehicles that rely on electronic pad wear monitoring, including A4, A5, Q7, Q8, S4, S5, S8, SQ7, SQ8, RS5, RS6 Avant, and RS7 Sportback applications.
Part number 355252791 is designed with durable injection-molded construction to handle demanding driving conditions and help maintain reliable brake wear signal performance. If you are replacing a rear brake pad wear sensor on an Audi A4 Quattro, Audi Q7, or Audi S5 Sportback, this sensor supports the factory monitoring system with the correct harness length and connector style.
Key Features
- Disc brake pad wear sensor for rear brake applications
- 395 mm / 15.55 in wiring harness length
- Male connector for the vehicle-side interface
- Wiring harness included for installation-ready replacement
- Injection-molded construction for durability in harsh environments
- Technical Information Number: P8713
- Pagid part number 355252791
Detailed Product Information
Pagid 355252791 is a rear disc brake pad wear sensor intended for vehicles equipped with electronic brake wear monitoring. The sensor is built to match the demands of modern Audi brake systems and is suited for models such as the Audi A4 allroad, A5 Sportback, A8 Quattro, Q7, Q8, RS5 Sportback, RS6 Avant, RS7 Sportback, S4, S5, S8, SQ7, and SQ8. This part cross-references Monroe Shocks & Struts (e.g., 172286, 182286) for the same application.
For shoppers searching for a rear brake pad wear sensor for Audi A4 Quattro, rear brake pad wear sensor for Audi Q7, or Pagid 355252791 for Audi S5, this part provides the fitment and connector details needed for a proper replacement. It is also listed for select RS Q8, RS6 Avant, and RS7 Sportback applications with ceramic brake exclusions noted where applicable.
What This Part Helps Address
- Brake wear warning light staying on after pad service
- Damaged or broken rear pad wear sensor wiring
- Fault codes related to brake pad wear monitoring
- Intermittent brake wear signal loss from heat or road exposure
- Replacement needs after rear brake pad and rotor service
Installation Notes and Tips
Installation requires qualified personnel. Confirm rear axle fitment, connector style, and harness routing before installation. Inspect the brake pad wear sensor path for abrasion points, damaged clips, or heat exposure, and verify the sensor seats correctly in the pad carrier and brake pad groove. After installation, clear any stored wear-related fault codes and confirm the warning system resets properly.
Quality Assurance
HELLA brake pad wear sensor engineering is referenced by the manufacturer description, with emphasis on precise fitment, durable injection-molded construction, and dependable performance across varied driving conditions. Pagid part number 355252791 is built for rear disc brake monitoring on supported Audi applications and is identified with Technical Information Number P8713.
Product Information
Product Information
Shipping & Returns
Shipping & Returns
Description
Rear Brake Pad Wear Sensor for Audi Applications
This Pagid disc brake pad wear sensor is built for rear brake systems and uses a 395 mm wiring harness with a male connector for a direct-style replacement. It is engineered for Audi vehicles that rely on electronic pad wear monitoring, including A4, A5, Q7, Q8, S4, S5, S8, SQ7, SQ8, RS5, RS6 Avant, and RS7 Sportback applications.
Part number 355252791 is designed with durable injection-molded construction to handle demanding driving conditions and help maintain reliable brake wear signal performance. If you are replacing a rear brake pad wear sensor on an Audi A4 Quattro, Audi Q7, or Audi S5 Sportback, this sensor supports the factory monitoring system with the correct harness length and connector style.
Key Features
- Disc brake pad wear sensor for rear brake applications
- 395 mm / 15.55 in wiring harness length
- Male connector for the vehicle-side interface
- Wiring harness included for installation-ready replacement
- Injection-molded construction for durability in harsh environments
- Technical Information Number: P8713
- Pagid part number 355252791
Detailed Product Information
Pagid 355252791 is a rear disc brake pad wear sensor intended for vehicles equipped with electronic brake wear monitoring. The sensor is built to match the demands of modern Audi brake systems and is suited for models such as the Audi A4 allroad, A5 Sportback, A8 Quattro, Q7, Q8, RS5 Sportback, RS6 Avant, RS7 Sportback, S4, S5, S8, SQ7, and SQ8. This part cross-references Monroe Shocks & Struts (e.g., 172286, 182286) for the same application.
For shoppers searching for a rear brake pad wear sensor for Audi A4 Quattro, rear brake pad wear sensor for Audi Q7, or Pagid 355252791 for Audi S5, this part provides the fitment and connector details needed for a proper replacement. It is also listed for select RS Q8, RS6 Avant, and RS7 Sportback applications with ceramic brake exclusions noted where applicable.
What This Part Helps Address
- Brake wear warning light staying on after pad service
- Damaged or broken rear pad wear sensor wiring
- Fault codes related to brake pad wear monitoring
- Intermittent brake wear signal loss from heat or road exposure
- Replacement needs after rear brake pad and rotor service
Installation Notes and Tips
Installation requires qualified personnel. Confirm rear axle fitment, connector style, and harness routing before installation. Inspect the brake pad wear sensor path for abrasion points, damaged clips, or heat exposure, and verify the sensor seats correctly in the pad carrier and brake pad groove. After installation, clear any stored wear-related fault codes and confirm the warning system resets properly.
Quality Assurance
HELLA brake pad wear sensor engineering is referenced by the manufacturer description, with emphasis on precise fitment, durable injection-molded construction, and dependable performance across varied driving conditions. Pagid part number 355252791 is built for rear disc brake monitoring on supported Audi applications and is identified with Technical Information Number P8713.
