PowerStop S2754 Disc Brake Caliper Set - Rear
Rear Brake Caliper for Toyota MR2 Spyder
PowerStop S2754 is a rear disc brake caliper set built for the 2000-2002 Toyota MR2 Spyder. It replaces the stock rear caliper with a remanufactured, high-heat red powder-coated unit that is made to bolt directly into place and stand out behind stock or custom wheels.
PowerStop’s Rear High-Heat Red Powder Coated Brake Calipers line focuses on performance-oriented replacement calipers with corrosion-resistant finishing and careful assembly. For MR2 Spyder rear brake service, S2754 combines a floating caliper design, a 44.30 mm steel piston, and a mounting bracket included for a direct-fit rear brake repair.
- Fits 2000-2002 Toyota MR2 Spyder, rear
- PowerStop part number S2754
- Remanufactured in Chicago, IL
- High-temperature red powder-coated finish
- Floating caliper design with 44.30 mm piston diameter
- Cast iron caliper body with steel piston
- Caliper slides included
- Mounting bracket included
- Pressure tested for piston operation and leak prevention
- Assembled with new pistons, seals, dust boots, bleeder screws, and stainless steel brake pad abutment clips
Product Details
PowerStop S2754 is engineered for drivers replacing a worn or sticking rear caliper on the Toyota MR2 Spyder. The red powder-coated surface helps resist rust and corrosion while making the caliper easier to clean. Each unit is pressure tested, then assembled with new internal service components and high-temperature EPDM rubber dust boots plus silicone lubricant for smoother operation in demanding conditions. If you are searching for a rear brake caliper set for a 2000-2002 Toyota MR2 Spyder, S2754 is a direct-fit option built around the original rear brake layout.
This part cross-references Monroe Shocks & Struts (e.g., 172286, 182286) for the same application.
Common Repair Uses
- Rear brake caliper leakage
- Sticking or seized rear caliper piston
- Uneven rear brake pad wear
- Corrosion on the rear caliper housing
- Brake drag or reduced rear braking response
Installation Notes
Verify rear fitment on the 2000-2002 Toyota MR2 Spyder before installation. Transfer or replace brake pads and related wear items as needed, and bleed the hydraulic system after caliper replacement. Confirm slide movement, piston operation, and brake line sealing before returning the vehicle to service.
Quality Assurance
PowerStop remanufactures these calipers and brackets in its Chicago, IL facility and pressure tests each caliper to verify piston function and check for leaks. The assembly uses new pistons, seals, slide pins where applicable, dust boots, bleeder screws, and stainless steel brake pad abutment clips for consistent service quality.
PowerStop S2754 Disc Brake Caliper Set - Rear
Rear Brake Caliper for Toyota MR2 Spyder
PowerStop S2754 is a rear disc brake caliper set built for the 2000-2002 Toyota MR2 Spyder. It replaces the stock rear caliper with a remanufactured, high-heat red powder-coated unit that is made to bolt directly into place and stand out behind stock or custom wheels.
PowerStop’s Rear High-Heat Red Powder Coated Brake Calipers line focuses on performance-oriented replacement calipers with corrosion-resistant finishing and careful assembly. For MR2 Spyder rear brake service, S2754 combines a floating caliper design, a 44.30 mm steel piston, and a mounting bracket included for a direct-fit rear brake repair.
- Fits 2000-2002 Toyota MR2 Spyder, rear
- PowerStop part number S2754
- Remanufactured in Chicago, IL
- High-temperature red powder-coated finish
- Floating caliper design with 44.30 mm piston diameter
- Cast iron caliper body with steel piston
- Caliper slides included
- Mounting bracket included
- Pressure tested for piston operation and leak prevention
- Assembled with new pistons, seals, dust boots, bleeder screws, and stainless steel brake pad abutment clips
Product Details
PowerStop S2754 is engineered for drivers replacing a worn or sticking rear caliper on the Toyota MR2 Spyder. The red powder-coated surface helps resist rust and corrosion while making the caliper easier to clean. Each unit is pressure tested, then assembled with new internal service components and high-temperature EPDM rubber dust boots plus silicone lubricant for smoother operation in demanding conditions. If you are searching for a rear brake caliper set for a 2000-2002 Toyota MR2 Spyder, S2754 is a direct-fit option built around the original rear brake layout.
This part cross-references Monroe Shocks & Struts (e.g., 172286, 182286) for the same application.
Common Repair Uses
- Rear brake caliper leakage
- Sticking or seized rear caliper piston
- Uneven rear brake pad wear
- Corrosion on the rear caliper housing
- Brake drag or reduced rear braking response
Installation Notes
Verify rear fitment on the 2000-2002 Toyota MR2 Spyder before installation. Transfer or replace brake pads and related wear items as needed, and bleed the hydraulic system after caliper replacement. Confirm slide movement, piston operation, and brake line sealing before returning the vehicle to service.
Quality Assurance
PowerStop remanufactures these calipers and brackets in its Chicago, IL facility and pressure tests each caliper to verify piston function and check for leaks. The assembly uses new pistons, seals, slide pins where applicable, dust boots, bleeder screws, and stainless steel brake pad abutment clips for consistent service quality.
Product Information
Product Information
Shipping & Returns
Shipping & Returns
Description
Rear Brake Caliper for Toyota MR2 Spyder
PowerStop S2754 is a rear disc brake caliper set built for the 2000-2002 Toyota MR2 Spyder. It replaces the stock rear caliper with a remanufactured, high-heat red powder-coated unit that is made to bolt directly into place and stand out behind stock or custom wheels.
PowerStop’s Rear High-Heat Red Powder Coated Brake Calipers line focuses on performance-oriented replacement calipers with corrosion-resistant finishing and careful assembly. For MR2 Spyder rear brake service, S2754 combines a floating caliper design, a 44.30 mm steel piston, and a mounting bracket included for a direct-fit rear brake repair.
- Fits 2000-2002 Toyota MR2 Spyder, rear
- PowerStop part number S2754
- Remanufactured in Chicago, IL
- High-temperature red powder-coated finish
- Floating caliper design with 44.30 mm piston diameter
- Cast iron caliper body with steel piston
- Caliper slides included
- Mounting bracket included
- Pressure tested for piston operation and leak prevention
- Assembled with new pistons, seals, dust boots, bleeder screws, and stainless steel brake pad abutment clips
Product Details
PowerStop S2754 is engineered for drivers replacing a worn or sticking rear caliper on the Toyota MR2 Spyder. The red powder-coated surface helps resist rust and corrosion while making the caliper easier to clean. Each unit is pressure tested, then assembled with new internal service components and high-temperature EPDM rubber dust boots plus silicone lubricant for smoother operation in demanding conditions. If you are searching for a rear brake caliper set for a 2000-2002 Toyota MR2 Spyder, S2754 is a direct-fit option built around the original rear brake layout.
This part cross-references Monroe Shocks & Struts (e.g., 172286, 182286) for the same application.
Common Repair Uses
- Rear brake caliper leakage
- Sticking or seized rear caliper piston
- Uneven rear brake pad wear
- Corrosion on the rear caliper housing
- Brake drag or reduced rear braking response
Installation Notes
Verify rear fitment on the 2000-2002 Toyota MR2 Spyder before installation. Transfer or replace brake pads and related wear items as needed, and bleed the hydraulic system after caliper replacement. Confirm slide movement, piston operation, and brake line sealing before returning the vehicle to service.
Quality Assurance
PowerStop remanufactures these calipers and brackets in its Chicago, IL facility and pressure tests each caliper to verify piston function and check for leaks. The assembly uses new pistons, seals, slide pins where applicable, dust boots, bleeder screws, and stainless steel brake pad abutment clips for consistent service quality.
