PowerStop Z47-2018 Disc Brake Pad Set - Front or Rear
PowerStop Z47 MD and Fleet Brake Pads
PowerStop Z47-2018 brake pads are built for medium-duty and last-mile fleet vehicles that operate at full GVW on a daily basis. This semi-metallic, carbon-fiber reinforced pad set is engineered for consistent stopping performance, reduced downtime, and lower cost-per-mile in severe-duty service.
For Ford Super Duty brake pad replacement needs, the Z47-2018 brings a performance-grade friction formula with hardware details that support a cleaner, more complete brake service. It is a practical choice for fleet maintenance where uptime and repeatable braking matter.
Key Features
- Semi-metallic friction material with carbon-fiber reinforcement
- Performance-grade pad set for medium-duty and fleet use
- Mechanically attached friction material for high shear resistance
- Slotted, chamfered, and scorched friction surface for consistent bedding
- Pad wear sensor included with mechanical sensor type
- Pad shims included for added fit and noise control
- Premium stainless-steel hardware included
- Outer and inner pad thickness: 20.5 mm
Product Details
The Power Stop Z47 MD and Fleet Carbon-Fiber Semi-Met Brake Pads with Hardware Kit are part of the Z47 MD and Fleet product line, which focuses on severe-duty braking for commercial vehicles that spend long hours under load. The semi-metallic compound is reinforced with carbon fiber to improve durability in demanding stop-and-go operation. The friction material is mechanically attached to the backing plate for added shear resistance, and the pad design includes slotted, chamfered, and scorched surfaces to support stable braking performance.
This part number, Z47-2018, is a direct-fit brake pad set for select Ford Super Duty applications and is also referenced by HC3Z 2001-B and HC3Z 2200-D for the same application. If you are searching for Ford Super Duty brake pads, Z47-2018 offers a fleet-focused upgrade path for vehicles that run heavy loads and need dependable brake response.
What It Helps Address
- Brake fade during repeated heavy-duty stops
- Premature pad wear in full-GVW fleet operation
- Noise and vibration from worn or uneven brake pads
- Reduced braking consistency in stop-and-go delivery routes
- Brake service downtime caused by incomplete pad and hardware replacement
Installation Notes and Tips
Inspect rotors, calipers, and slide hardware before installation. Clean all mating surfaces, verify pad orientation, and follow the vehicle service procedure for bedding-in new pads after installation. The included stainless-steel hardware supports a more complete brake job, and the pad wear sensor should be connected according to the vehicle’s original brake wear monitoring setup.
For Ford Super Duty brake pad replacement, confirm the vehicle’s brake configuration against the listed interchange numbers and service information before ordering. The Z47-2018 part number should be matched to the correct axle position and brake package for the application.
Quality Assurance
PowerStop designs the Z47 MD and Fleet line for severe-duty fleet service, with a friction formula focused on durability, shear resistance, and repeatable braking performance. The Z47-2018 is built to meet the demands of medium-duty and last-mile vehicles operating under load.
Original: $105.97
-65%$105.97
$37.09PowerStop Z47-2018 Disc Brake Pad Set - Front or Rear
PowerStop Z47 MD and Fleet Brake Pads
PowerStop Z47-2018 brake pads are built for medium-duty and last-mile fleet vehicles that operate at full GVW on a daily basis. This semi-metallic, carbon-fiber reinforced pad set is engineered for consistent stopping performance, reduced downtime, and lower cost-per-mile in severe-duty service.
For Ford Super Duty brake pad replacement needs, the Z47-2018 brings a performance-grade friction formula with hardware details that support a cleaner, more complete brake service. It is a practical choice for fleet maintenance where uptime and repeatable braking matter.
Key Features
- Semi-metallic friction material with carbon-fiber reinforcement
- Performance-grade pad set for medium-duty and fleet use
- Mechanically attached friction material for high shear resistance
- Slotted, chamfered, and scorched friction surface for consistent bedding
- Pad wear sensor included with mechanical sensor type
- Pad shims included for added fit and noise control
- Premium stainless-steel hardware included
- Outer and inner pad thickness: 20.5 mm
Product Details
The Power Stop Z47 MD and Fleet Carbon-Fiber Semi-Met Brake Pads with Hardware Kit are part of the Z47 MD and Fleet product line, which focuses on severe-duty braking for commercial vehicles that spend long hours under load. The semi-metallic compound is reinforced with carbon fiber to improve durability in demanding stop-and-go operation. The friction material is mechanically attached to the backing plate for added shear resistance, and the pad design includes slotted, chamfered, and scorched surfaces to support stable braking performance.
This part number, Z47-2018, is a direct-fit brake pad set for select Ford Super Duty applications and is also referenced by HC3Z 2001-B and HC3Z 2200-D for the same application. If you are searching for Ford Super Duty brake pads, Z47-2018 offers a fleet-focused upgrade path for vehicles that run heavy loads and need dependable brake response.
What It Helps Address
- Brake fade during repeated heavy-duty stops
- Premature pad wear in full-GVW fleet operation
- Noise and vibration from worn or uneven brake pads
- Reduced braking consistency in stop-and-go delivery routes
- Brake service downtime caused by incomplete pad and hardware replacement
Installation Notes and Tips
Inspect rotors, calipers, and slide hardware before installation. Clean all mating surfaces, verify pad orientation, and follow the vehicle service procedure for bedding-in new pads after installation. The included stainless-steel hardware supports a more complete brake job, and the pad wear sensor should be connected according to the vehicle’s original brake wear monitoring setup.
For Ford Super Duty brake pad replacement, confirm the vehicle’s brake configuration against the listed interchange numbers and service information before ordering. The Z47-2018 part number should be matched to the correct axle position and brake package for the application.
Quality Assurance
PowerStop designs the Z47 MD and Fleet line for severe-duty fleet service, with a friction formula focused on durability, shear resistance, and repeatable braking performance. The Z47-2018 is built to meet the demands of medium-duty and last-mile vehicles operating under load.
Product Information
Product Information
Shipping & Returns
Shipping & Returns
Description
PowerStop Z47 MD and Fleet Brake Pads
PowerStop Z47-2018 brake pads are built for medium-duty and last-mile fleet vehicles that operate at full GVW on a daily basis. This semi-metallic, carbon-fiber reinforced pad set is engineered for consistent stopping performance, reduced downtime, and lower cost-per-mile in severe-duty service.
For Ford Super Duty brake pad replacement needs, the Z47-2018 brings a performance-grade friction formula with hardware details that support a cleaner, more complete brake service. It is a practical choice for fleet maintenance where uptime and repeatable braking matter.
Key Features
- Semi-metallic friction material with carbon-fiber reinforcement
- Performance-grade pad set for medium-duty and fleet use
- Mechanically attached friction material for high shear resistance
- Slotted, chamfered, and scorched friction surface for consistent bedding
- Pad wear sensor included with mechanical sensor type
- Pad shims included for added fit and noise control
- Premium stainless-steel hardware included
- Outer and inner pad thickness: 20.5 mm
Product Details
The Power Stop Z47 MD and Fleet Carbon-Fiber Semi-Met Brake Pads with Hardware Kit are part of the Z47 MD and Fleet product line, which focuses on severe-duty braking for commercial vehicles that spend long hours under load. The semi-metallic compound is reinforced with carbon fiber to improve durability in demanding stop-and-go operation. The friction material is mechanically attached to the backing plate for added shear resistance, and the pad design includes slotted, chamfered, and scorched surfaces to support stable braking performance.
This part number, Z47-2018, is a direct-fit brake pad set for select Ford Super Duty applications and is also referenced by HC3Z 2001-B and HC3Z 2200-D for the same application. If you are searching for Ford Super Duty brake pads, Z47-2018 offers a fleet-focused upgrade path for vehicles that run heavy loads and need dependable brake response.
What It Helps Address
- Brake fade during repeated heavy-duty stops
- Premature pad wear in full-GVW fleet operation
- Noise and vibration from worn or uneven brake pads
- Reduced braking consistency in stop-and-go delivery routes
- Brake service downtime caused by incomplete pad and hardware replacement
Installation Notes and Tips
Inspect rotors, calipers, and slide hardware before installation. Clean all mating surfaces, verify pad orientation, and follow the vehicle service procedure for bedding-in new pads after installation. The included stainless-steel hardware supports a more complete brake job, and the pad wear sensor should be connected according to the vehicle’s original brake wear monitoring setup.
For Ford Super Duty brake pad replacement, confirm the vehicle’s brake configuration against the listed interchange numbers and service information before ordering. The Z47-2018 part number should be matched to the correct axle position and brake package for the application.
Quality Assurance
PowerStop designs the Z47 MD and Fleet line for severe-duty fleet service, with a friction formula focused on durability, shear resistance, and repeatable braking performance. The Z47-2018 is built to meet the demands of medium-duty and last-mile vehicles operating under load.
