Delphi TD4702W Suspension Stabilizer Bar Bushing Kit - Front Outer, Front To Control Arm or Front To Lower Control Arm
Delphi TD4702W Suspension Stabilizer Bar Bushing Kit - Front Outer, Front To Control Arm or Front To Lower Control Arm
Delphi TD4702W Front Stabilizer Bar Bushing Kit
Restore front suspension support with the Delphi TD4702W stabilizer bar bushing kit. Built with rubber construction and standard replacement dimensions, this part is made for front outer and control arm mounting locations on select Lexus and Toyota applications.
Compatible with 2010-2022 Lexus GX460, 2010-2022 Toyota 4Runner, and 2004-2009 Lexus GX470, this Delphi TD4702W bushing kit is a direct-fit option for front suspension service. Delphi applies OE-level dimensional and material analysis to help match the original part profile for proper fit and function.
Key Features
- Rubber bushing material with black finish
- Standard replacement grade for front suspension service
- Inside diameter: 27.0 mm
- Width: 43.5 mm
- Height: 47.21 mm
- Position-specific fitment for front outer, front to control arm, and front to lower control arm applications
- Cross-reference: Toyota 48849-60040 and MOOG K200618
Detailed Description
The Delphi TD4702W is a suspension stabilizer bar bushing kit engineered for front-end service on Lexus GX460, Lexus GX470, and Toyota 4Runner models. Its rubber construction helps maintain stabilizer bar support at the control arm interface, while the listed dimensions support accurate OE-style replacement fitment. Delphi subjects its OE and aftermarket steering and suspension components to extreme temperature and salt-spray testing, along with dimensional and material analysis, to help maintain consistent performance and compatibility.
This part number, TD4702W, is a practical choice when replacing worn front stabilizer bar bushings on vehicles that show looseness or noise in the front suspension. The Delphi TD4702W also cross-references Toyota 48849-60040 and MOOG K200618 for the same application.
Common Issues This Part Can Address
- Front suspension clunking or rattling over bumps
- Excessive play at the stabilizer bar mounting point
- Worn or cracked rubber bushings
- Reduced front-end stability from deteriorated bushing support
- Noise caused by movement between the sway bar and control arm area
Installation Notes and Tips
Verify the exact front suspension position on your vehicle before ordering, since this part is listed for front outer, front to control arm, and front to lower control arm locations. Confirm bushing dimensions against the original component and inspect the stabilizer bar, control arm contact surfaces, and surrounding hardware for wear before installation. For 2010-2022 Toyota 4Runner, 2010-2022 Lexus GX460, and 2004-2009 Lexus GX470 applications, match the position shown in the application tab to ensure correct placement.
Quality Assurance
Delphi uses OE-focused engineering and testing for its steering and suspension portfolio, including extreme temperature exposure and extended salt-spray testing to evaluate durability. The brand also performs dimensional and material analysis to support OE-to-aftermarket compatibility.
Delphi TD4702W Suspension Stabilizer Bar Bushing Kit - Front Outer, Front To Control Arm or Front To Lower Control Arm
Delphi TD4702W Front Stabilizer Bar Bushing Kit
Restore front suspension support with the Delphi TD4702W stabilizer bar bushing kit. Built with rubber construction and standard replacement dimensions, this part is made for front outer and control arm mounting locations on select Lexus and Toyota applications.
Compatible with 2010-2022 Lexus GX460, 2010-2022 Toyota 4Runner, and 2004-2009 Lexus GX470, this Delphi TD4702W bushing kit is a direct-fit option for front suspension service. Delphi applies OE-level dimensional and material analysis to help match the original part profile for proper fit and function.
Key Features
- Rubber bushing material with black finish
- Standard replacement grade for front suspension service
- Inside diameter: 27.0 mm
- Width: 43.5 mm
- Height: 47.21 mm
- Position-specific fitment for front outer, front to control arm, and front to lower control arm applications
- Cross-reference: Toyota 48849-60040 and MOOG K200618
Detailed Description
The Delphi TD4702W is a suspension stabilizer bar bushing kit engineered for front-end service on Lexus GX460, Lexus GX470, and Toyota 4Runner models. Its rubber construction helps maintain stabilizer bar support at the control arm interface, while the listed dimensions support accurate OE-style replacement fitment. Delphi subjects its OE and aftermarket steering and suspension components to extreme temperature and salt-spray testing, along with dimensional and material analysis, to help maintain consistent performance and compatibility.
This part number, TD4702W, is a practical choice when replacing worn front stabilizer bar bushings on vehicles that show looseness or noise in the front suspension. The Delphi TD4702W also cross-references Toyota 48849-60040 and MOOG K200618 for the same application.
Common Issues This Part Can Address
- Front suspension clunking or rattling over bumps
- Excessive play at the stabilizer bar mounting point
- Worn or cracked rubber bushings
- Reduced front-end stability from deteriorated bushing support
- Noise caused by movement between the sway bar and control arm area
Installation Notes and Tips
Verify the exact front suspension position on your vehicle before ordering, since this part is listed for front outer, front to control arm, and front to lower control arm locations. Confirm bushing dimensions against the original component and inspect the stabilizer bar, control arm contact surfaces, and surrounding hardware for wear before installation. For 2010-2022 Toyota 4Runner, 2010-2022 Lexus GX460, and 2004-2009 Lexus GX470 applications, match the position shown in the application tab to ensure correct placement.
Quality Assurance
Delphi uses OE-focused engineering and testing for its steering and suspension portfolio, including extreme temperature exposure and extended salt-spray testing to evaluate durability. The brand also performs dimensional and material analysis to support OE-to-aftermarket compatibility.
Product Information
Product Information
Shipping & Returns
Shipping & Returns
Description
Delphi TD4702W Front Stabilizer Bar Bushing Kit
Restore front suspension support with the Delphi TD4702W stabilizer bar bushing kit. Built with rubber construction and standard replacement dimensions, this part is made for front outer and control arm mounting locations on select Lexus and Toyota applications.
Compatible with 2010-2022 Lexus GX460, 2010-2022 Toyota 4Runner, and 2004-2009 Lexus GX470, this Delphi TD4702W bushing kit is a direct-fit option for front suspension service. Delphi applies OE-level dimensional and material analysis to help match the original part profile for proper fit and function.
Key Features
- Rubber bushing material with black finish
- Standard replacement grade for front suspension service
- Inside diameter: 27.0 mm
- Width: 43.5 mm
- Height: 47.21 mm
- Position-specific fitment for front outer, front to control arm, and front to lower control arm applications
- Cross-reference: Toyota 48849-60040 and MOOG K200618
Detailed Description
The Delphi TD4702W is a suspension stabilizer bar bushing kit engineered for front-end service on Lexus GX460, Lexus GX470, and Toyota 4Runner models. Its rubber construction helps maintain stabilizer bar support at the control arm interface, while the listed dimensions support accurate OE-style replacement fitment. Delphi subjects its OE and aftermarket steering and suspension components to extreme temperature and salt-spray testing, along with dimensional and material analysis, to help maintain consistent performance and compatibility.
This part number, TD4702W, is a practical choice when replacing worn front stabilizer bar bushings on vehicles that show looseness or noise in the front suspension. The Delphi TD4702W also cross-references Toyota 48849-60040 and MOOG K200618 for the same application.
Common Issues This Part Can Address
- Front suspension clunking or rattling over bumps
- Excessive play at the stabilizer bar mounting point
- Worn or cracked rubber bushings
- Reduced front-end stability from deteriorated bushing support
- Noise caused by movement between the sway bar and control arm area
Installation Notes and Tips
Verify the exact front suspension position on your vehicle before ordering, since this part is listed for front outer, front to control arm, and front to lower control arm locations. Confirm bushing dimensions against the original component and inspect the stabilizer bar, control arm contact surfaces, and surrounding hardware for wear before installation. For 2010-2022 Toyota 4Runner, 2010-2022 Lexus GX460, and 2004-2009 Lexus GX470 applications, match the position shown in the application tab to ensure correct placement.
Quality Assurance
Delphi uses OE-focused engineering and testing for its steering and suspension portfolio, including extreme temperature exposure and extended salt-spray testing to evaluate durability. The brand also performs dimensional and material analysis to support OE-to-aftermarket compatibility.
