Dorman 522-942 Suspension Control Arm and Ball Joint Assembly - Front Right Lower
Dorman 522-942 Suspension Control Arm Assembly
This Dorman suspension control arm and ball joint assembly is a direct replacement for the original equipment on select vehicles, including the 1992 Mitsubishi Diamante front right lower position through 5/92. Built for OE-style fit and function, Dorman 522-942 supports smooth ride quality, directional stability, and predictable suspension movement.
For shoppers searching for a 1992 Mitsubishi Diamante front right lower control arm and ball joint assembly, this replacement is built around the original application and mounting layout. The boxed steel arm, pre-installed ball joint, and included bushings help simplify service on the front suspension.
Key Features
- Direct replacement suspension control arm and ball joint assembly
- Fits 1992 Mitsubishi Diamante, front right lower, to 5/92
- Pre-greased for immediate service
- Ball joint is installed and uses a press-in mounting type
- Threaded ball joint stud with 14 mm thread diameter
- Steel boxed control arm with black finish
- Rubber bushings included
- Mounting hardware included
Detailed Description
Dorman 522-942 is engineered as an OE-style suspension control arm assembly for the front right lower position on the 1992 Mitsubishi Diamante. The steel boxed arm construction, rubber bushings, and installed ball joint are selected to match the original suspension layout and restore proper geometry after wear or damage. This part number, 522-942, is a practical replacement choice when the original arm shows looseness, bushing deterioration, or ball joint wear.
This part cross-references Monroe Shocks & Struts (e.g., 172286, 182286) for the same application.
What It Helps Address
- Front-end clunking from worn control arm bushings
- Steering wander or reduced directional stability
- Uneven tire wear caused by suspension looseness
- Excess play from a worn ball joint
- Ride quality issues related to damaged lower suspension components
Installation Notes and Tips
Verify the vehicle application before installation: 1992 Mitsubishi Diamante, front right lower, to 5/92. Confirm the press-in ball joint style, threaded stud size, and mounting hole dimensions match the original suspension setup. Because the ball joint is already installed and the assembly is pre-greased, service time may be reduced compared with rebuilding the arm separately. After installation, inspect alignment and suspension fasteners according to factory procedures.
Quality Assurance
Dorman uses an industry-focused evaluation process for this suspension control arm assembly to help maintain consistent ride behavior, straight-line stability, and predictable handling characteristics. Dorman 522-942 is built as a direct replacement for the original equipment configuration on the listed Mitsubishi Diamante application.
Dorman 522-942 Suspension Control Arm and Ball Joint Assembly - Front Right Lower
Dorman 522-942 Suspension Control Arm Assembly
This Dorman suspension control arm and ball joint assembly is a direct replacement for the original equipment on select vehicles, including the 1992 Mitsubishi Diamante front right lower position through 5/92. Built for OE-style fit and function, Dorman 522-942 supports smooth ride quality, directional stability, and predictable suspension movement.
For shoppers searching for a 1992 Mitsubishi Diamante front right lower control arm and ball joint assembly, this replacement is built around the original application and mounting layout. The boxed steel arm, pre-installed ball joint, and included bushings help simplify service on the front suspension.
Key Features
- Direct replacement suspension control arm and ball joint assembly
- Fits 1992 Mitsubishi Diamante, front right lower, to 5/92
- Pre-greased for immediate service
- Ball joint is installed and uses a press-in mounting type
- Threaded ball joint stud with 14 mm thread diameter
- Steel boxed control arm with black finish
- Rubber bushings included
- Mounting hardware included
Detailed Description
Dorman 522-942 is engineered as an OE-style suspension control arm assembly for the front right lower position on the 1992 Mitsubishi Diamante. The steel boxed arm construction, rubber bushings, and installed ball joint are selected to match the original suspension layout and restore proper geometry after wear or damage. This part number, 522-942, is a practical replacement choice when the original arm shows looseness, bushing deterioration, or ball joint wear.
This part cross-references Monroe Shocks & Struts (e.g., 172286, 182286) for the same application.
What It Helps Address
- Front-end clunking from worn control arm bushings
- Steering wander or reduced directional stability
- Uneven tire wear caused by suspension looseness
- Excess play from a worn ball joint
- Ride quality issues related to damaged lower suspension components
Installation Notes and Tips
Verify the vehicle application before installation: 1992 Mitsubishi Diamante, front right lower, to 5/92. Confirm the press-in ball joint style, threaded stud size, and mounting hole dimensions match the original suspension setup. Because the ball joint is already installed and the assembly is pre-greased, service time may be reduced compared with rebuilding the arm separately. After installation, inspect alignment and suspension fasteners according to factory procedures.
Quality Assurance
Dorman uses an industry-focused evaluation process for this suspension control arm assembly to help maintain consistent ride behavior, straight-line stability, and predictable handling characteristics. Dorman 522-942 is built as a direct replacement for the original equipment configuration on the listed Mitsubishi Diamante application.
Product Information
Product Information
Shipping & Returns
Shipping & Returns
Description
Dorman 522-942 Suspension Control Arm Assembly
This Dorman suspension control arm and ball joint assembly is a direct replacement for the original equipment on select vehicles, including the 1992 Mitsubishi Diamante front right lower position through 5/92. Built for OE-style fit and function, Dorman 522-942 supports smooth ride quality, directional stability, and predictable suspension movement.
For shoppers searching for a 1992 Mitsubishi Diamante front right lower control arm and ball joint assembly, this replacement is built around the original application and mounting layout. The boxed steel arm, pre-installed ball joint, and included bushings help simplify service on the front suspension.
Key Features
- Direct replacement suspension control arm and ball joint assembly
- Fits 1992 Mitsubishi Diamante, front right lower, to 5/92
- Pre-greased for immediate service
- Ball joint is installed and uses a press-in mounting type
- Threaded ball joint stud with 14 mm thread diameter
- Steel boxed control arm with black finish
- Rubber bushings included
- Mounting hardware included
Detailed Description
Dorman 522-942 is engineered as an OE-style suspension control arm assembly for the front right lower position on the 1992 Mitsubishi Diamante. The steel boxed arm construction, rubber bushings, and installed ball joint are selected to match the original suspension layout and restore proper geometry after wear or damage. This part number, 522-942, is a practical replacement choice when the original arm shows looseness, bushing deterioration, or ball joint wear.
This part cross-references Monroe Shocks & Struts (e.g., 172286, 182286) for the same application.
What It Helps Address
- Front-end clunking from worn control arm bushings
- Steering wander or reduced directional stability
- Uneven tire wear caused by suspension looseness
- Excess play from a worn ball joint
- Ride quality issues related to damaged lower suspension components
Installation Notes and Tips
Verify the vehicle application before installation: 1992 Mitsubishi Diamante, front right lower, to 5/92. Confirm the press-in ball joint style, threaded stud size, and mounting hole dimensions match the original suspension setup. Because the ball joint is already installed and the assembly is pre-greased, service time may be reduced compared with rebuilding the arm separately. After installation, inspect alignment and suspension fasteners according to factory procedures.
Quality Assurance
Dorman uses an industry-focused evaluation process for this suspension control arm assembly to help maintain consistent ride behavior, straight-line stability, and predictable handling characteristics. Dorman 522-942 is built as a direct replacement for the original equipment configuration on the listed Mitsubishi Diamante application.
