Dorman 533-475 Suspension Stabilizer Bar Bushing Kit - Front To Control Arm
OE-Style Stabilizer Bar Bushing Replacement
Dorman 533-475 is a suspension stabilizer bar bushing kit built for specific front-to-control-arm applications on Chevrolet Lumina, Chevrolet Monte Carlo, Buick Regal, Oldsmobile Cutlass Supreme, and Pontiac Grand Prix models. It uses rubber construction and standard replacement dimensions to restore a secure stabilizer bar mount where the original bushing has worn or deteriorated.
For shoppers searching for a front stabilizer bar bushing kit for 1997-2001 Chevrolet Lumina or a sway bar bushing replacement for 1988-1996 Pontiac Grand Prix, this part number 533-475 provides a direct-fit service solution for the listed vehicles.
- Rubber bushing construction for OE-style suspension service
- Inside diameter: 24 mm
- Outside diameter: 1.58 in.
- Assembled length: 1.76 in.
- Standard replacement grade for listed applications
- Bracket not included
- Grease fitting not included
Detailed Product Overview
This Dorman suspension stabilizer bar bushing kit is precision-engineered and tested to replace the original equipment bushing on specific vehicles. It is designed for front-to-control-arm mounting locations and is sized to match the listed OE-style fitment requirements. The rubber material helps maintain stabilizer bar location and reduce unwanted movement at the mounting point, which is important for consistent front suspension operation on vehicles such as the Buick Regal, Chevrolet Lumina, and Pontiac Grand Prix.
This part cross-references MOOG Chassis Products K6641 for the same application.
What This Part Helps Address
- Clunking or knocking from the front stabilizer bar area
- Excessive play at the stabilizer bar mounting point
- Worn, cracked, or compressed original bushings
- Loose-feeling front suspension response over bumps
- Noise caused by deteriorated sway bar isolation material
Installation Notes and Fitment
Fits 1997-2001 Chevrolet Lumina, front to control arm. Fits 1997-1999 Chevrolet Monte Carlo, front to control arm. Fits 1988-1997 Oldsmobile Cutlass Supreme, front to control arm. Fits 1988-1996 Buick Regal, front to control arm. Fits 1990-1996 Chevrolet Lumina, front to control arm. Fits 1995-1996 Chevrolet Monte Carlo, front to control arm. Fits 1988-1996 Pontiac Grand Prix, front to control arm.
Confirm the stabilizer bar diameter and mounting style before installation. This kit does not include a bracket, and no grease fitting is provided. Use the listed vehicle application and position data to verify fitment before service.
Quality Assurance
Dorman manufactures this stabilizer bar bushing kit as a standard replacement part for the specified OE applications. It is engineered and tested to meet the needs of the listed vehicles and mounting position.
Dorman 533-475 Suspension Stabilizer Bar Bushing Kit - Front To Control Arm
OE-Style Stabilizer Bar Bushing Replacement
Dorman 533-475 is a suspension stabilizer bar bushing kit built for specific front-to-control-arm applications on Chevrolet Lumina, Chevrolet Monte Carlo, Buick Regal, Oldsmobile Cutlass Supreme, and Pontiac Grand Prix models. It uses rubber construction and standard replacement dimensions to restore a secure stabilizer bar mount where the original bushing has worn or deteriorated.
For shoppers searching for a front stabilizer bar bushing kit for 1997-2001 Chevrolet Lumina or a sway bar bushing replacement for 1988-1996 Pontiac Grand Prix, this part number 533-475 provides a direct-fit service solution for the listed vehicles.
- Rubber bushing construction for OE-style suspension service
- Inside diameter: 24 mm
- Outside diameter: 1.58 in.
- Assembled length: 1.76 in.
- Standard replacement grade for listed applications
- Bracket not included
- Grease fitting not included
Detailed Product Overview
This Dorman suspension stabilizer bar bushing kit is precision-engineered and tested to replace the original equipment bushing on specific vehicles. It is designed for front-to-control-arm mounting locations and is sized to match the listed OE-style fitment requirements. The rubber material helps maintain stabilizer bar location and reduce unwanted movement at the mounting point, which is important for consistent front suspension operation on vehicles such as the Buick Regal, Chevrolet Lumina, and Pontiac Grand Prix.
This part cross-references MOOG Chassis Products K6641 for the same application.
What This Part Helps Address
- Clunking or knocking from the front stabilizer bar area
- Excessive play at the stabilizer bar mounting point
- Worn, cracked, or compressed original bushings
- Loose-feeling front suspension response over bumps
- Noise caused by deteriorated sway bar isolation material
Installation Notes and Fitment
Fits 1997-2001 Chevrolet Lumina, front to control arm. Fits 1997-1999 Chevrolet Monte Carlo, front to control arm. Fits 1988-1997 Oldsmobile Cutlass Supreme, front to control arm. Fits 1988-1996 Buick Regal, front to control arm. Fits 1990-1996 Chevrolet Lumina, front to control arm. Fits 1995-1996 Chevrolet Monte Carlo, front to control arm. Fits 1988-1996 Pontiac Grand Prix, front to control arm.
Confirm the stabilizer bar diameter and mounting style before installation. This kit does not include a bracket, and no grease fitting is provided. Use the listed vehicle application and position data to verify fitment before service.
Quality Assurance
Dorman manufactures this stabilizer bar bushing kit as a standard replacement part for the specified OE applications. It is engineered and tested to meet the needs of the listed vehicles and mounting position.
Product Information
Product Information
Shipping & Returns
Shipping & Returns
Description
OE-Style Stabilizer Bar Bushing Replacement
Dorman 533-475 is a suspension stabilizer bar bushing kit built for specific front-to-control-arm applications on Chevrolet Lumina, Chevrolet Monte Carlo, Buick Regal, Oldsmobile Cutlass Supreme, and Pontiac Grand Prix models. It uses rubber construction and standard replacement dimensions to restore a secure stabilizer bar mount where the original bushing has worn or deteriorated.
For shoppers searching for a front stabilizer bar bushing kit for 1997-2001 Chevrolet Lumina or a sway bar bushing replacement for 1988-1996 Pontiac Grand Prix, this part number 533-475 provides a direct-fit service solution for the listed vehicles.
- Rubber bushing construction for OE-style suspension service
- Inside diameter: 24 mm
- Outside diameter: 1.58 in.
- Assembled length: 1.76 in.
- Standard replacement grade for listed applications
- Bracket not included
- Grease fitting not included
Detailed Product Overview
This Dorman suspension stabilizer bar bushing kit is precision-engineered and tested to replace the original equipment bushing on specific vehicles. It is designed for front-to-control-arm mounting locations and is sized to match the listed OE-style fitment requirements. The rubber material helps maintain stabilizer bar location and reduce unwanted movement at the mounting point, which is important for consistent front suspension operation on vehicles such as the Buick Regal, Chevrolet Lumina, and Pontiac Grand Prix.
This part cross-references MOOG Chassis Products K6641 for the same application.
What This Part Helps Address
- Clunking or knocking from the front stabilizer bar area
- Excessive play at the stabilizer bar mounting point
- Worn, cracked, or compressed original bushings
- Loose-feeling front suspension response over bumps
- Noise caused by deteriorated sway bar isolation material
Installation Notes and Fitment
Fits 1997-2001 Chevrolet Lumina, front to control arm. Fits 1997-1999 Chevrolet Monte Carlo, front to control arm. Fits 1988-1997 Oldsmobile Cutlass Supreme, front to control arm. Fits 1988-1996 Buick Regal, front to control arm. Fits 1990-1996 Chevrolet Lumina, front to control arm. Fits 1995-1996 Chevrolet Monte Carlo, front to control arm. Fits 1988-1996 Pontiac Grand Prix, front to control arm.
Confirm the stabilizer bar diameter and mounting style before installation. This kit does not include a bracket, and no grease fitting is provided. Use the listed vehicle application and position data to verify fitment before service.
Quality Assurance
Dorman manufactures this stabilizer bar bushing kit as a standard replacement part for the specified OE applications. It is engineered and tested to meet the needs of the listed vehicles and mounting position.
