Walker 270-1050 Vehicle Speed Sensor Connector
Vehicle Speed Sensor Connector for OE-Style Repair
Walker 270-1050 is a vehicle speed sensor connector built for OE-style electrical repair on a wide range of GM trucks, SUVs, and performance cars. It uses molded connector housing, pre-terminated leads, and copper wiring to restore a secure connection where the original pigtail has heat damage, corrosion, or broken terminals.
Compatible With 1988-2005 Chevrolet Blazer, S10, Astro, K1500, Tahoe, Corvette, Camaro, and related GMC and Oldsmobile applications, this Walker pigtail is a direct-fit repair solution for vehicle speed sensor service. The 270-1050 is designed for standard crimp or solder repair methods and matches factory-style connector geometry for straightforward replacement.
Key Features
- Walker 270-1050 vehicle speed sensor connector
- OE replacement pigtail with molded connector housing
- Pre-terminated leads for electrical repair work
- 14-gauge copper wire with heat-, oil-, and chemical-resistant insulation
- 2 blade terminals, male connector with female terminals
- 133.35 mm wiring harness length
- Direct replacement for damaged harness connectors on GM applications
Detailed Product Overview
Walker Products electrical pigtails are engineered to replace damaged wiring harness connectors across critical vehicle systems. This connector is built to restore reliable signal transfer at the vehicle speed sensor and other OE-style mating components without modifying the original sensor or harness interface. The 270-1050 is a practical repair part for drivability and electrical service on Chevrolet Blazer, GMC Jimmy, and Chevrolet S10 platforms, along with additional GM truck and SUV applications listed in the fitment data.
This part cross-references AC Delco PT216 and Dorman 645-1050 for the same application.
What It Is Used For
- Broken or brittle vehicle speed sensor connector housings
- Corroded terminals causing intermittent electrical contact
- Heat-damaged pigtails near the engine bay, transmission tunnel, or underbody
- Drivability faults related to unstable speed sensor wiring
- Repairing OE-style harness connections on GM trucks and SUVs
Installation Notes and Tips
Install the Walker 270-1050 using standard crimp or solder repair methods. Match the connector orientation and terminal layout before splicing, and inspect the mating sensor or component for bent pins, corrosion, or contamination before reconnecting. This connector is listed for specific GM applications, including 1998-2005 Chevrolet Blazer, 1998-2004 Chevrolet S10, 1998-2004 GMC Sonoma, 1999 Chevrolet Tahoe, and 1995-1998 Chevrolet K1500 with transfer case-related notes where shown in the fitment data.
Quality Assurance
Walker electrical pigtails are built to OE specifications for wire capacity, flexibility, and resistance to heat, oil, and chemicals. The 270-1050 is designed as an OE-style replacement connector for dependable electrical repair on factory systems.
Walker 270-1050 Vehicle Speed Sensor Connector
Vehicle Speed Sensor Connector for OE-Style Repair
Walker 270-1050 is a vehicle speed sensor connector built for OE-style electrical repair on a wide range of GM trucks, SUVs, and performance cars. It uses molded connector housing, pre-terminated leads, and copper wiring to restore a secure connection where the original pigtail has heat damage, corrosion, or broken terminals.
Compatible With 1988-2005 Chevrolet Blazer, S10, Astro, K1500, Tahoe, Corvette, Camaro, and related GMC and Oldsmobile applications, this Walker pigtail is a direct-fit repair solution for vehicle speed sensor service. The 270-1050 is designed for standard crimp or solder repair methods and matches factory-style connector geometry for straightforward replacement.
Key Features
- Walker 270-1050 vehicle speed sensor connector
- OE replacement pigtail with molded connector housing
- Pre-terminated leads for electrical repair work
- 14-gauge copper wire with heat-, oil-, and chemical-resistant insulation
- 2 blade terminals, male connector with female terminals
- 133.35 mm wiring harness length
- Direct replacement for damaged harness connectors on GM applications
Detailed Product Overview
Walker Products electrical pigtails are engineered to replace damaged wiring harness connectors across critical vehicle systems. This connector is built to restore reliable signal transfer at the vehicle speed sensor and other OE-style mating components without modifying the original sensor or harness interface. The 270-1050 is a practical repair part for drivability and electrical service on Chevrolet Blazer, GMC Jimmy, and Chevrolet S10 platforms, along with additional GM truck and SUV applications listed in the fitment data.
This part cross-references AC Delco PT216 and Dorman 645-1050 for the same application.
What It Is Used For
- Broken or brittle vehicle speed sensor connector housings
- Corroded terminals causing intermittent electrical contact
- Heat-damaged pigtails near the engine bay, transmission tunnel, or underbody
- Drivability faults related to unstable speed sensor wiring
- Repairing OE-style harness connections on GM trucks and SUVs
Installation Notes and Tips
Install the Walker 270-1050 using standard crimp or solder repair methods. Match the connector orientation and terminal layout before splicing, and inspect the mating sensor or component for bent pins, corrosion, or contamination before reconnecting. This connector is listed for specific GM applications, including 1998-2005 Chevrolet Blazer, 1998-2004 Chevrolet S10, 1998-2004 GMC Sonoma, 1999 Chevrolet Tahoe, and 1995-1998 Chevrolet K1500 with transfer case-related notes where shown in the fitment data.
Quality Assurance
Walker electrical pigtails are built to OE specifications for wire capacity, flexibility, and resistance to heat, oil, and chemicals. The 270-1050 is designed as an OE-style replacement connector for dependable electrical repair on factory systems.
Product Information
Product Information
Shipping & Returns
Shipping & Returns
Description
Vehicle Speed Sensor Connector for OE-Style Repair
Walker 270-1050 is a vehicle speed sensor connector built for OE-style electrical repair on a wide range of GM trucks, SUVs, and performance cars. It uses molded connector housing, pre-terminated leads, and copper wiring to restore a secure connection where the original pigtail has heat damage, corrosion, or broken terminals.
Compatible With 1988-2005 Chevrolet Blazer, S10, Astro, K1500, Tahoe, Corvette, Camaro, and related GMC and Oldsmobile applications, this Walker pigtail is a direct-fit repair solution for vehicle speed sensor service. The 270-1050 is designed for standard crimp or solder repair methods and matches factory-style connector geometry for straightforward replacement.
Key Features
- Walker 270-1050 vehicle speed sensor connector
- OE replacement pigtail with molded connector housing
- Pre-terminated leads for electrical repair work
- 14-gauge copper wire with heat-, oil-, and chemical-resistant insulation
- 2 blade terminals, male connector with female terminals
- 133.35 mm wiring harness length
- Direct replacement for damaged harness connectors on GM applications
Detailed Product Overview
Walker Products electrical pigtails are engineered to replace damaged wiring harness connectors across critical vehicle systems. This connector is built to restore reliable signal transfer at the vehicle speed sensor and other OE-style mating components without modifying the original sensor or harness interface. The 270-1050 is a practical repair part for drivability and electrical service on Chevrolet Blazer, GMC Jimmy, and Chevrolet S10 platforms, along with additional GM truck and SUV applications listed in the fitment data.
This part cross-references AC Delco PT216 and Dorman 645-1050 for the same application.
What It Is Used For
- Broken or brittle vehicle speed sensor connector housings
- Corroded terminals causing intermittent electrical contact
- Heat-damaged pigtails near the engine bay, transmission tunnel, or underbody
- Drivability faults related to unstable speed sensor wiring
- Repairing OE-style harness connections on GM trucks and SUVs
Installation Notes and Tips
Install the Walker 270-1050 using standard crimp or solder repair methods. Match the connector orientation and terminal layout before splicing, and inspect the mating sensor or component for bent pins, corrosion, or contamination before reconnecting. This connector is listed for specific GM applications, including 1998-2005 Chevrolet Blazer, 1998-2004 Chevrolet S10, 1998-2004 GMC Sonoma, 1999 Chevrolet Tahoe, and 1995-1998 Chevrolet K1500 with transfer case-related notes where shown in the fitment data.
Quality Assurance
Walker electrical pigtails are built to OE specifications for wire capacity, flexibility, and resistance to heat, oil, and chemicals. The 270-1050 is designed as an OE-style replacement connector for dependable electrical repair on factory systems.
